A spiral chute is a stationary gravity separation device: an inclined helical trough down which dilute slurry flows as a thin film. Heavy, round particles in the 0.1–2 mm band sink through the film, reach the slow layer at the trough wall and migrate to the inside of the helix; light grains ride the fast outer stream. Splitters at the discharge cut concentrate, middlings and tailings. It consumes no power and no reagents, and its entire performance depends on feed preparation, steady flow and splitter discipline.
· Separation comes from two overlapping flows: fast downstream film plus slow secondary circulation across the trough.
· The sorting happens mostly in the first two or three turns; the rest of the helix is transport.
· Working window: 0.1–2 mm feed, 20–40% solids, 1–3 t/h per start, constant flow.
· Concentration criterion above ~1.5 is the precondition; below ~1.25 spirals make middlings, not concentrate.
· Zero moving parts means failures are silent — liner wear, splitter drift and feed surge are the three killers.
· Middlings return to feed; final cleaning belongs to tables or centrifugal concentrators.
|
Item |
Typical Range / Practice |
|
Feed size |
0.1–2 mm (best 0.15–1 mm) |
|
Desliming cut |
Minus ~50 µm removed first |
|
Feed density |
20–40% solids |
|
Capacity per start |
1–3 t/h |
|
Column height |
2–4 m, 5–7 turns |
|
Power demand |
None (feed pump only) |
|
Products |
Concentrate, middlings, tailings |
|
Best duties |
Tin, tungsten, chromite, ilmenite, zircon, iron ore, alluvial gold |
|
Liner life (first turns) |
Months to a year+, duty dependent |
A spiral chute is a semicircular trough wound into a vertical helix, built from glass-reinforced plastic or polyurethane-faced fibreglass, mounted on a light frame. Double-start and triple-start units run two or three independent streams down one column. "Spiral concentrator" and "spiral chute" are used interchangeably in the industry; the useful distinctions are pitch, diameter, start count and liner material. The device belongs to the same family as shaking tables and centrifugal concentrators — the Gravity class — but it sits at the low-cost, high-tonnage end, as shown on the Spiral Chutes page. The full combined specification is on the Spiral Chute | Spiral Concentrator listing.
Downstream flow. A feed box spreads slurry into a thin film that accelerates down the helix. The trough curvature makes the outside of the bend run faster than the inside — the same physics that carries a river around the outside of a bend.
Secondary circulation. The same curvature rolls the film across the trough: surface layer outward, bottom layer inward. Heavy, spherical particles drop through the film early, enter the slow near-wall layer, and are carried toward the inner edge. Wash water fed along the inner radius keeps the collected heavy strand fluid and prevents packing.
Splitting. By the bottom turn, three zones span the trough width: a slow heavy strand inside, a fast light stream outside, a middling band between. Adjustable splitters cut them into separate launders. Where the splitters sit decides the grade-recovery trade-off, and the correct position moves with feed grade.
Two starts, one frame, gravity feed: the machine asks for a flat pad and a steady head, nothing more.
· No power at the machine. Operating cost is one feed pump and one water line.
· No reagents. Nothing to dose, nothing to neutralise downstream.
· High capacity per floor area. Double-start columns halve the footprint per tonne.
· Forgiving of operator skill. One walk-through per shift covers a whole row.
· Fast to install. A flat pad, a feed head, done.
· Graceful degradation. Worn liners reduce recovery gradually, not suddenly.
· Tin and tungsten: cassiterite and wolframite against quartz — the classic duty. In November 2026, Peru's Minsur filed for environmental approval to retreat about 651,000 tonnes of B3 tailings at its San Rafael tin mine, investing roughly US$22 million to recover residual cassiterite through the existing plant; sand-size tin recovery is exactly this machine's territory.
· Mineral sands: ilmenite, rutile, zircon and monazite roughed from quartz in wet plants.
· Chromite: metallurgical and beach deposits, after washing and desliming.
· Iron ore: gravity roughing of fine hematite and goethite where flotation is not justified.
· Alluvial gold: roughing ahead of tables or concentrators, with the washing and screening machines in the Gold Process Equipment range handling the coarse end.
· Slag and garnet recovery: anywhere a workable density ratio survives.
|
Liner / Body Material |
Strengths |
Watch-outs |
|
Glass-reinforced plastic (GRP) |
Low cost, smooth surface, light |
Paint and gelcoat wear first at top turns |
|
Polyurethane-faced GRP |
Best wear life, stable surface |
Higher unit cost |
|
Cast basalt / ceramic inserts |
Extreme abrasion resistance in hot spots |
Only used at the first two turns |
|
FRP body, steel frame |
Standard bank construction |
Frame corrosion in wet climates |
Material choice follows duty: polyurethane facing pays for itself where feed is abrasive or tonnage is high; plain GRP is fine for small, gentle circuits. Replacement sections, feed boxes and splitters are supplied as matched sets in the Gravity Separation Spares range.
|
Device |
Strength |
Weakness |
Best Role |
|
Spiral chute |
Cheap, high tonnage, no power |
Poor below ~50 µm |
Roughing and scavenging |
|
Shaking table |
Highest concentrate grade |
Low capacity, needs power |
Final cleaning |
|
Centrifugal concentrator |
Recovers fine heavy grains |
Power, moving parts |
Fine gold, upgrading |
|
Jig |
Handles coarse feed |
Lower ratio limits |
선술집 시간 : 2026-11-16 09:55:17 >> 뉴스 명부
연락처 세부 사항
TOGETHER HTL LTD
담당자: Mr. Maple 전화 번호: +86 17778255675 팩스: 86--311-80690567 |