Abrasive screening is the separation of hard, wear-causing material — mineral ore, crushed rock or aggregate — where the dominant cost driver is progressive surface wear of the screening medium rather than blockage or sizing accuracy alone.
Sliding abrasion occurs as particles travel across the deck and gradually remove material from the screening surface. Impact wear occurs where large particles land at the feed end and deliver concentrated local loads.
A Tufflex screen panel is a rope-based screening medium in which polyurethane-coated wire rope and polyurethane-coated synthetic cord are joined to form apertures. It sits between conventional WIRED & STEEL SCREEN MESH and solid POLYURETHANE & RUBBER SCREEN PANELS.
The panel works at three levels.
Contact surface. The polyurethane coating around the wire rope is the surface that meets the feed. Polyurethane resists sliding abrasion well, so the contact area degrades more slowly than exposed metal wire in comparable duty. Coating thickness and formulation govern how much of that advantage is realised.
Structural behaviour. Because the cloth is rope-based rather than a solid moulded panel, it retains flexibility. The cloth moves under vibration, which helps release lodged particles and reduces the tendency for fines to pack into apertures. Aperture geometry and welding configuration — fully versus partially welded — determine how much movement occurs.
Flow behaviour. In side-tensioned arrangements the synthetic cord runs parallel to the hooked edge and behaves similarly to rider bars, guiding oversize along the deck while fines migrate toward openings. This supports stratification and raises the proportion of feed that actually reaches an aperture.
Together these raise effective open area during operation. That is the figure that governs capacity — not the nominal open area on a product drawing.
Longer service life than woven wire in sliding-abrasion duty, where wire wears out before it blinds.
More open area than solid polyurethane, because the rope structure leaves more of the deck available for material passage.
Flexible cloth behaviour that helps release lodged particles and reduces pegging pressure.
Configurable aperture geometry, allowing square or rectangular openings matched to the cut size.
Lower maintenance frequency, since fewer changeouts mean less labour and less planned downtime.
Measurable cost advantage when evaluated as cost per tonne processed rather than price per panel.
None of these benefits is unconditional. In severe impact zones, or where feed is exceptionally coarse, other media remain better suited to the duty.
Tufflex is evaluated where abrasive wear, not blockage alone, is the maintenance driver.
Gold ore and alluvial feed with hard, angular particles and variable moisture.
Iron ore and copper ore scalping and sizing ahead of GRINDING, where wire wear is frequent.
Aggregates and crushed rock production, where hard limestone or granite shortens wire life.
Silica sand duty where both abrasion and fine sizing matter.
Coal preparation where clay partings and abrasive shale occur together.
Lead zinc ore and nickel ore in mixed wet and abrasive duty.
Tailings and slurry duty where abrasive solids and moisture combine.
The panel typically sits between size reduction in CRUSHING and downstream CLASSIFICATION. Wear-driven screen failures there propagate as unstable feed sizing into the grinding and classification circuit.
| Property | Tufflex | Woven Wire Mesh | Solid Polyurethane Panel | Rubber Screen Media |
|---|---|---|---|---|
| Sliding abrasion resistance | Good | Moderate | Good–excellent | Good |
| Impact resistance | Moderate | Low | Moderate | Excellent |
| Open area | Good | High | Lower | Moderate |
| Anti-pegging | Good (flexible cloth) | Poor on near-size | Moderate | Moderate |
| Noise | Low | High | Low | Low |
| Best application | Abrasive duty with open-area needs | Clean dry high-capacity duty | Wet screening, high wear | Coarse high-impact feed zones |
The table is a starting point, not a verdict. Woven wire remains correct where abrasion is mild and capacity dominates. Rubber remains correct where impact dominates. Tufflex earns its place where sliding abrasion is the cost driver but solid polyurethane would sacrifice too much open area.
| Scenario | Dominant Problem | Recommended Direction |
|---|---|---|
| Hard angular ore, wire wears out fast | Sliding abrasion | Tufflex with aperture matched to cut size |
| Large rock at high drop height | Impact | Rubber at feed end, Tufflex downstream |
| Mild abrasion, capacity constrained | Open area | Woven wire or hybrid deck |
| Wet sticky feed with clay | Blinding | Polyurethane surface plus moisture control |
| Fine cut with tight tolerance | Sizing accuracy | POLYURETHANE FINE SCREEN PANEL |
| Mixed wear and pegging | Both | Tufflex trial with separate wear benchmarking |
| Industry | Typical Ore | Wear Risk | Screening Stage |
|---|---|---|---|
| Gold | Gold ore, alluvial | High abrasion | Pre-concentration, GOLD PROCESS EQUIPMENT feed prep |
| Iron ore | Iron ore, hematite | High abrasion | Scalping and product sizing |
| Copper | Copper ore | High abrasion | SAG discharge screening |
| Coal | Coal with shale partings | Moderate | Desliming and preparation |
| Aggregates | Limestone, granite | High abrasion | Product classification |
| Industrial minerals | Silica sand | Moderate–high | Fine screening and dewatering |
| Battery minerals | Lithium ore | Moderate | Classification feed prep |
| Base metals | Lead zinc ore, nickel ore | High | Grinding circuit screening |
| Fertilizer | Phosphate ore | Moderate | Wet screening |
| Critical minerals | Rare earth ore | Moderate | Fine classification |
1. Identify the wear mechanism. Inspect worn panels. Even surface loss across the deck indicates sliding abrasion. Concentrated damage at the feed end indicates impact. The two need different answers, and a single panel may not solve both.
선술집 시간 : 2026-11-03 09:13:48 >> 뉴스 명부
담당자: Mr. Maple
전화 번호: +86 17778255675
팩스: 86--311-80690567
