Woven wire mesh is a screening medium made from metal wires woven into a grid to form apertures. It is characterised by high open area, relatively low cost and predictable sizing accuracy, but is susceptible to wear, fatigue and breakage in abrasive duty.
Polyurethane screen panels are moulded elastomer screening media available in tensioned or modular designs. They offer wear resistance, impact absorption, noise reduction and design flexibility, at the cost of generally lower open area.
Effective open area is the proportion of the screen surface actually available for material passage during operation, after blockage. It is the figure that governs capacity, not the nominal open area on a drawing.
The comparison between wire mesh and polyurethane comes down to how each material handles the forces applied by the feed.
Abrasion. Wire mesh thins as particles slide across it, eventually breaking. Polyurethane removes material more slowly because the elastomer deforms under particle contact and recovers, rather than abrading directly.
Impact. Wire fatigues under repeated impact and crack propagation is fast. Polyurethane absorbs energy through elastic deformation, which extends life at the feed zone where large particles land.
Noise. Steel transmits impact energy as sound. Polyurethane absorbs it, producing a quieter deck. The difference is measurable and is sometimes the deciding factor on multi-screen plants.
Open area. Wire mesh can be woven with high open area because the wires are thin. Polyurethane requires material between apertures for structural integrity, which reduces open area. This matters most in fine screening where the cut size is close to the aperture dimension.
Blockage. Wire mesh can peg near-size particles and blind under wet clay. Polyurethane's flexible structure and moulded aperture profiles can reduce both, particularly with tapered or slotted designs.
Longer wear life in abrasive mineral duty, reducing changeout frequency.
Impact absorption at the feed zone without the fatigue cracking seen in wire.
Lower noise levels on multi-screen installations, improving working conditions.
Modular replacement allowing position-specific changeout rather than full-deck replacement.
Flexible aperture design with square, rectangular, slotted or dewatering profiles.
Lower total operating cost when evaluated as cost per tonne over full service life.
Iron ore and copper ore screening where abrasive wear drives changeout frequency.
Quarry and aggregate production where sharp crushed rock damages wire quickly.
Coal preparation where wet conditions and clay content cause blinding.
Gold ore processing where high-value feed makes downtime expensive.
Fine screening duty where aperture geometry and open area both matter.
Dewatering decks where slot design and drainage behaviour are critical.
These duties sit between size reduction in CRUSHING and downstream CLASSIFICATION or DEWATERING. A media change alters what reaches the next stage, which is why the decision should include the circuit, not only the deck.
| Property | Woven Wire Mesh | Polyurethane Panel | Rubber Screen Media | PU Fine Screen Panel |
|---|---|---|---|---|
| Open area | High | Moderate | Moderate | High at fine cuts |
| Abrasion resistance | Moderate | Good | Good–excellent | Good |
| Impact resistance | Low | Moderate | Excellent | Moderate |
| Noise | High | Low | Low | Low |
| Modular replacement | Rarely | Common | Common | Common |
| Fine separation accuracy | Good | Moderate | Limited | Good |
| Best application | Clean dry high-capacity duty | Abrasive duty with moderate open area | Coarse high-impact zones | Fine screening and dewatering |
| Scenario | Dominant Problem | Recommended Direction |
|---|---|---|
| Wire wears out in weeks on abrasive ore | Abrasion | POLYURETHANE & RUBBER SCREEN PANELS with appropriate formulation |
| Feed end cracking from impact | Impact | PU impact panel at feed zone; hybrid deck |
| Multiple screens creating noise problems | Noise | PU panels across the deck |
| Full-deck replacement costly and slow | Maintenance | Modular PU panels with position-based replacement |
| Fine screening with tight cut size | Open area and accuracy | POLYURETHANE FINE SCREEN PANEL or retain WIRED & STEEL SCREEN MESH |
| Dewatering duty with drainage needs | Slot design | PU dewatering panel matched to DEWATERING requirements |
| Industry | Typical Material | Wire Wear Risk | Replacement Case |
|---|---|---|---|
| Iron ore | Hematite, magnetite | High | Strong case for PU in abrasive duty |
| Copper | Copper ore | High | Strong case, especially at feed zone |
| Gold | Gold ore, alluvial | Moderate–high | Case depends on cut size and feed |
| Coal | Coal with clay | Moderate | Case depends on wet handling |
| Aggregates | Limestone, granite | High | Strong case for abrasive crushed rock |
| Sand and gravel | Natural sand | Moderate | Case depends on open area requirement |
| Industrial minerals | Silica sand | Moderate–high | Fine screen evaluation required |
| Base metals | Lead zinc, nickel ore | High | Strong case for abrasive duty |
| Phosphate | Phosphate ore | Moderate | Case depends on wet handling |
| Tailings | Slurry, fine solids | Moderate | Case depends on drainage requirements |
1. Diagnose the failure mode. Wire thinning and breakage indicate abrasion. Feed-end cracking indicates impact. Full-deck failure after days indicates wrong a
담당자: Mr. Maple
전화 번호: +86 17778255675
팩스: 86--311-80690567